For a complete wiring diagram Refer to Section 8WWhen Monitored:With the ignition on and the O2 1/1 Sensor at operating temperature.Set Condition:The ECM detects an open on the (K89) O2 1/1 Positive Current Control circuit for 2.0 seconds.Possible CausesINTERMITTENT DTC(K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO VOLTAGE(K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO GROUND(K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO THE (F344) FUSED ASD RELAY OUTPUT 2 CIRCUIT(K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO THE (K79) O2 1/1 HEATER CONTROL CIRCUIT(K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT OPEN OR HIGH RESISTANCEOXYGEN SENSORENGINE CONTROL MODULE (ECM)Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.(Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)1. DTC IS ACTIVEIgnition on, engine not running.With the scan tool, Clear DTCs in the Engine Control Module (ECM).Start the engine.Allow the engine to reach normal operating temperature.Monitor the scan tool for at least two minutes.With the scan tool, select View DTCs.Is the status Active for this DTC?YesGo To 2 NoRefer to the *CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure.(Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)2. (K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO VOLTAGE

Turn the ignition off.Disconnect the Oxygen Sensor harness connector.Disconnect the Engine Control Module (ECM) harness connector.Remove the ASD Relay from the TIPM.Connect a jumper wire between cavity 30 and cavity 87 of the ASD Relay Connector.Turn the ignition on.Measure the voltage of the (K89) O2 1/1 Positive Current Control circuit in the Oxygen Sensor harness connector.Is there any voltage present?YesRepair the (K89) O2 1/1 Positive Current Control circuit for a short to voltage. Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)NoGo to 33. (K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO GROUND

Turn the ignition off.Remove the jumper wire and install the ASD Relay.Measure the resistance between ground and the (K89) O2 1/1 Positive Current Control circuit in the Oxygen Sensor harness connector.Is the resistance above 1000 ohms?YesGo to 4NoRepair the (K89) O2 1/1 Positive Current Control circuit for a short to ground. Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)4. (K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO THE (F344) FUSED ASD RELAY OUTPUT 2 CIRCUIT

Measure the resistance between the (K89) O2 1/1 Positive Current Control circuit and the (F344) Fused ASD Relay Output 2 circuit in the Oxygen Sensor harness connector.Is the resistance above 1000 ohms?YesGo to 5NoRepair the (K89) O2 1/1 Positive Current Control circuit for a short to the (F344) Fused ASD Relay Output 2 circuit.Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)5. (K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT SHORTED TO THE (K79) O2 1/1 HEATER CONTROL CIRCUIT

Measure the resistance between the (K89) O2 1/1 Positive Current Control circuit and the (K79) O2 1/1 Heater Control circuit in the Oxygen Sensor harness connector.Is the resistance above 1000 ohms?YesGo to 6NoRepair the (K89) O2 1/1 Positive Current Control circuit for a short to the (K79) O2 1/1 Heater Control circuit.Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)6. (K89) O2 1/1 POSITIVE CURRENT CONTROL CIRCUIT OPEN OR HIGH RESISTANCE

Measure the resistance of the (K89) O2 1/1 Positive Current Control circuit between the Oxygen Sensor harness connector and the Engine Control Module (ECM) harness connector.Is the resistance below 10.0 ohms?YesGo to 7NoRepair the (K89) 02 1/1 Positive Current Control circuit for an open circuit or high resistance.Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)7. OXYGEN SENSORTurn the ignition off.Connect the Engine Control Module (ECM) harness connector.Replace the Oxygen Sensor in accordance with the Service Information.Start the engine.Allow the engine to reach normal operating temperature.Monitor the scan tool for at least two minutes.With the scan tool, select View DTCs.Is the status Active for this DTC?YesGo to 8NoTest Complete.Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)8. ENGINE CONTROL MODULE (ECM)Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Oxygen Sensor and the Engine Control Module (ECM).Look for any chafed, pierced, pinched, or partially broken wires.Look for broken, bent, pushed out or corroded terminals.Monitor the scan tool data relative to this circuit and wiggle test the wiring and connectors.Look for the data to change or for the DTC to reset during the wiggle test.Refer to any Technical Service Bulletins that may apply.Were any problems found?YesRepair as necessary.Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)NoReplace the Engine Control Module (ECM) in accordance with the Service Information.Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - STANDARD PROCEDURE)