For a complete wiring diagram Refer to Section 8WThe Transmission system uses five pressure switches to monitor the fluid pressure in the L/R, 2C, 4C, UD, and OD clutch circuits. The pressure switches are continuously monitored for the correct states in each gear as shown.When Monitored:Continuously with the ignition on and engine running.Set Condition:The appropriate DTC is set if one of the pressure switches are open or closed at the wrong time in a given gear.Possible CausesRELATED TCM POWER INPUT DTCS PRESENTLINE PRESSURE DTCS PRESENTNO. 4 OR 6 CHECK BALL CUT OR DAMAGED(T9) OD PRESSURE SWITCH SENSE CIRCUIT OPEN(T9) OD PRESSURE SWITCH SENSE CIRCUIT SHORT TO GROUND(T9) OD PRESSURE SWITCH SENSE CIRCUIT SHORT TO OTHER CIRCUITSLOW LINE PRESSUREWIRING AND CONNECTORSCUT OD/REV PISTON SEALBROKEN OR MISSING OD/REV PISTON BLEED ORIFICEBROKEN REACTION SHAFT SUPPORT SEAL RINGPOOR MACHINING ON PUMP VALVE BODY FACEBROKEN OR MISSING DRIBBLER ORIFICE ASSEMBLY IN REACTION SHAFT SUPPORTTRANSMISSION SOLENOID/TRS ASSEMBLYCUT OD ACCUMULATOR PISTON SEALCRACKED OD ACCUMULATOR PISTONBROKEN OR MISSING OD BLEED ORIFICE IN MAIN VALVE BODYPOWERTRAIN CONTROL MODULEAlways perform the 45RFE/545RFE Pre-Diagnostic Troubleshooting Procedure before proceeding. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) GEARL/R2C4CUDODREVERSEOPENOPENOPENOPENOPENP/NCLOSED**OPENOPENOPENOPEN1STCLOSED*OPENOPENCLOSEDOPEN2NDOPENCLOSEDOPENCLOSEDOPEN2nd PRIMEOPENOPENCLOSEDCLOSEDOPEN3THOPENOPENOPENCLOSEDCLOSED4THOPENOPENCLOSEDOPENCLOSED5THOPENCLOSEDOPENOPENCLOSED*L/R is closed if output speed is below 100 rpm in Drive and Manual 2. L/R is closed in Manual 1.**May be open when rolling in Neutral or at low oil temperatures.1. CHECK DTCSWith the scan tool, read DTCs.Are there any TIPM TCM Power Control Circuit or TCM Power Input DTCs present?YesRefer to the Transmission category and perform the appropriate symptom. NoGo To 22. CHECK IF LINE PRESSURE DTCS ARE PRESENTWith the scan tool, read Transmission DTCs.Are there any Line Pressure DTCs present?YesRefer to the Transmission category and perform the appropriate symptom. NoGo To 33. CHECK FOR OTHER PRESSURE SWITCH DTCSWith the scan tool, read Transmission DTCs.Are there two or more other pressure switch rationality DTCs present in addition to P0871?YesGo To 5NoGo To 44. CHECK IF DTC IS CURRENTWith the scan tool, read and record the DTC EVENT DATA.Make sure to record all DTC EVENT DATA stored in the scan tool for future reference in this test procedure.Does the DTC EVENT DATA show data for P0871YesGo To 8NoRefer to the Transmission category and perform the appropriate symptom. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - DIAGNOSIS AND TESTING) 5. CHECK IF RELATED DTC IS PRESENTWith the scan tool, read and record the DTC EVENT DATA.Make sure to record all DTC EVENT DATA stored in the scan tool for future reference in this test procedure.Do all the pressure switches read CLOSED in the DTC EVENT DATA?YesRefer to the Transmission category and perform diagnostics for P0882. Follow instructions as if the DTC is current.(Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - DIAGNOSIS AND TESTING) NoGo To 66. CHECK IF PRESSURE SWITCHES READ OPENIn the DTC EVENT DATA recorded earlier, read the state of all pressure switches.Do all the pressure switches read open?YesGo To 7NoGo To 87. CHECK FOR LOW LINE PRESSUREIn the DTC EVENT DATA recorded earlier, compare the Line Pressure to the Desired Line Pressure.Is the Line Pressure less than 40 psi, and significantly below the Desired Line Pressure?YesRepair as necessary to correct low line pressure. Check fluid level and adjust as necessary. If fluid level is OK, check the Primary Oil Filter weal for a spit, crack , or improperly installed. If the filer and seal are OK, check the Main Regulator Valve in the Oil Pump. Refer to the Service Information for the above procedures.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoReplace the Transmission Solenoid/TRS Assembly per the Service Information. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE/TRANS SOLENOID/TRS ASSY - REMOVAL)Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST.8. CHECK IF IN PARK, NEUTRAL, OR REVERSEIgnition on, engine not running.With the scan tool, read and record the DTC EVENT DATA for P0871.Make sure to record all DTC EVENT DATA stored in the scan tool for future reference in this test procedure.Does the DTC EVENT DATA show the OD Pressure Switch DTC set while in Park, Neutral, or Reverse?YesGo To 18NoGo To 99. CHECK IF THE OD PRESSURE SWITCH WAS OPENRefer to the DTC EVENT DATA recorded earlier for P0871.Did the OD Pressure Switch read OPEN?YesGo To 10NoGo To 1510. CHECK FOR LOW LINE PRESSURERefer to the DTC EVENT DATA recorded earlier and compare the Line Pressure and the Desired Line Pressure.Is the Line Pressure less than 40 psi, and significantly below the Desired Line Pressure?YesRepair as necessary to correct low line pressure. Check the fluid level. Check the Primary Oil Filter seal for a split, crack, or improperly installed. Refer to the Service Information for the proper installation procedure. If the fluid level and filter are OK, check the Main Regulator Valve in the Oil Pump.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1111. CHECK THE (T9) OD PRESSURE SWITCH SENSE CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT

Turn the ignition off to the lock position.Disconnect all PCM harness connectors.Disconnect the Transmission Solenoid/TRS Assembly harness connector.Measure the resistance between the (T9) OD Pressure Switch Sense circuit and all other circuits in the Transmission Solenoid/TRS Assembly harness connector.Is the resistance below 5.0 ohms between the (T9) OD Pressure Switch Sense circuit and any other circuit(s) in the Transmission Solenoid/TRS Assembly harness connector?YesRepair the (T9) OD Pressure Switch Sense circuit for a short to another circuit(s).Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1212. CHECK TO SEE IF THE DTC RESETSReconnect all previously disconnected connectors.With the scan too, erase transmission DTCs.Test drive the vehicle, use the DTC EVENT DATA recorded earlier to help duplicate the conditions when the DTC originality set.Does the DTC P0871 reset?YesGo To 13NoGo To 2213. CHECK THE POWERTRAIN CONTROL MODULERemove the Transmission Control Relay.Operate the vehicle in Drive.Is the transmission slipping while in Drive?YesGo To 14NoUsing the schematics as a guide, check the Powertrain Control Module (PCM) terminals for corrosion, damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems are found, replace the PCM per the Service Information. With the scan tool, perform QUICK LEARN.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) 14. AIR CHECK TRANSMISSION CLUTCH OPERATIONPerform an Air Check Transmission Clutch Operation procedure per the Service Information.The OD/Rev piston contains a small bleed orifice, a small amount of leakage between the OD and Reverse hydraulic clutch circuits is considered normal.Is there excessive air leakage in any clutch circuit?YesCheck the OD/Rev piston seals and bleed orifice, reaction shaft support seal rings, dribbler orifice assemblies in the reaction shaft support and for poor machine on the pump valve body faces. Refer to the Service Information.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoRepair the Valve Body. Check the OD Accumulator piston and seals, OD bleed orifice, and No.6 check ball cuts or damage. If no problems are found in the Valve Body, replace the Transmission Solenoid/TRS Assembly. Refer to the Service Information for proper repair procedures.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) 15. CHECK THE PCM AND WIRINGTurn the ignition off to the lock position.Remove the Ignition Switch Feed fuse from the TIPM.Removal of the Ignition Switch Feed fuse from the TIPM will prevent the vehicle from being started in gear. The Ignition Switch Feed fuse must be removed from the TIPM. Failure to do so can result in personal injury or death.Install Transmission Simulator, Miller tool #8333.Ignition on, engine not running.With the Transmission Simulator, turn the Pressure Switch selector switch to OD.With the scan tool, monitor the OD Pressure Switch state while pressing the Pressure Switch Test button on the Transmission Simulator.Did the state of the OD Pressure Switch change from OPEN to CLOSED while pressing the Test button?YesGo To 16NoGo To 1816. CHECK IF THE NO. 4 AND/OR NO. 6 CHECK BALL IS CUT OR DAMAGEDWith the scan tool, erase previously stored DTC's and test drive the vehicle, use the DTC EVENT DATA to help duplicate the conditions when the DTC originality set. Note any DTCs that may set.Remove the Transmission Valve Body per the Service Information.Check the No. 4 and No. 6 Check Balls for cuts or damage.Is the No. 4 and/or No. 6 Check Ball cut or damaged?YesReplace the No. 4 and/or No. 6 Check Ball and check for clutch debris in the transmission oil pan. If there is excessive debris, perform internal repairs to the OD Clutch Assembly. Refer to the Service Information for proper repair procedures.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1717. CHECK THE TRANSMISSION SOLENOID/TRS ASSEMBLYDid the DTC P0871 reset during the test drive in the previous step?YesReplace the Transmission Solenoid/TRS Assembly per the Service Information. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE/TRANS SOLENOID/TRS ASSY - REMOVAL)Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 2218. CHECK THE (T9) OD PRESSURE SWITCH SENSE CIRCUIT FOR AN OPEN

Turn the ignition off to the lock position.Disconnect the PCM C4 harness connector and connect Miller tool #8815.Disconnect the Transmission Solenoid /TRS Assembly harness connectorDo not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install Miller tool #8815 to perform diagnosis.Measure the resistance of the (T9) OD Pressure Switch Sense circuit from the appropriate terminal of Miller tool #8815 to the Solenoid/TRS Assembly harness connector.Is the resistance above 5.0 ohms?YesRepair the (T9) OD Pressure Switch Sense circuit for an open.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1919. CHECK THE (T9) OD PRESSURE SWITCH SENSE CIRCUIT FOR A SHORT TO GROUND

Measure the resistance between ground and the (T9) OD Pressure Switch Sense circuit.Is the resistance below 5.0 ohms?YesRepair the (T9) OD Pressure Switch Sense circuit for a short to ground.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 2020. CHECK WIRING AND CONNECTORSUsing the schematics as a guide, inspect the wiring and connectors. Pay particular attention to all power and ground circuits.Were there any problems foundYesRepair as necessary.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 2121. CHECK THE POWERTRAIN CONTROL MODULEReconnect all previously disconnected connectors.Make sure all DTC EVENT DATA is recorded.With the scan tool, erase previously stored DTC's and test drive the vehicle, use the DTC EVENT DATA to help duplicate the conditions when the DTC originality set.Does the DTC P0871 reset?YesUsing the schematics as a guide, check the Powertrain Control Module (PCM) terminals for corrosion, damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems are found, replace the PCM per the Service Information. With the scan tool, perform QUICK LEARN.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 2222. INTERMITTENT WIRING AND CONNECTORSThe conditions necessary to set this DTC are not present at this time.Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.Wiggle the wires while checking for shorted and open circuits.With the scan tool, check the DTC EVENT DATA to help identify the conditions in which the DTC was set.Where there any problems found?YesRepair as necessary.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoTest Complete.