For a complete wiring diagram Refer to Section 8WThe Transmission system uses five pressure switches to monitor the fluid pressure in the L/R, 2C, 4C, UD, and OD clutch circuits. The pressure switches are continuously monitored for the correct states in each gear as shown.When Monitored:Continuously with the ignition on and engine running.Set Condition:This DTC is set if the UD pressure switch is in the wrong state for the current gear. For example, this code would be set if the UD pressure switch remained off while the transmission was in second gear.Possible CausesRELATED DTCS PRESENTLOW FLUID LEVELNO. 2 CHECK BALL CUT OR DAMAGEDLOW LINE PRESSURECRACKED OR MIS-INSTALLED SUMP FILTER OR SEALLOOSE COOLER RETURN SPIN ON FILTER (IF EQUIPPED)STICKING MAIN REGULATOR VALVE IN PUMP VALVE BODY(T29) UD PRESSURE SWITCH SENSE CIRCUIT OPEN(T29) UD PRESSURE SWITCH CIRCUIT SHORT TO GROUND(T29) UD PRESSURE SWITCH SENSE CIRCUIT SHORT TO ANOTHER CIRCUITSTRANSMISSION SOLENOID/TRS ASSEMBLYPOWERTRAIN CONTROL MODULEAlways perform the 45RFE/545RFE Pre-Diagnostic Troubleshooting Procedure before proceeding. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) GEARL/R2C4CUDODREVERSEOPENOPENOPENOPENOPENP/NCLOSED**OPENOPENOPENOPEN1STCLOSED*OPENOPENCLOSEDOPEN2NDOPENCLOSEDOPENCLOSEDOPEN2nd PRIMEOPENOPENCLOSEDCLOSEDOPEN3THOPENOPENOPENCLOSEDCLOSED4THOPENOPENCLOSEDOPENCLOSED5THOPENCLOSEDOPENOPENCLOSED*L/R is closed if output speed is below 100 rpm in Drive and Manual 2. L/R is closed in Manual 1.**May be open when rolling in Neutral or at low oil temperatures.1. CHECK IF RELATED DTCS ARE PRESENTWith the scan tool, check DTCs.Are there any TCM Power Input, TIPM TCM Power Control Circuit, Line Pressure, and/or Loss of Prime DTCs present?YesRefer to the Transmission category and perform the appropriate symptom. If a Loss of Prime DTC is present, perform its respective test first. NoGo To 22. CHECK FOR PRESSURE SWITCH DTCSAre there two or more other pressure switch rationality DTCs present in addition to P0876?YesGo To 3NoGo To 43. CHECK IF ALL PRESSURE SWITCHES READ CLOSEDWith the scan tool, read and record all DTC EVENT DATA.Make sure to record all DTC EVENT DATA stored in the scan tool for future reference in this test procedure.Does the DTC EVENT DATA show all pressure switches reading CLOSED?YesRefer to the Transmission category and perform the diagnostics for P0882. Diagnose the symptom as if the DTC is current.NoGo To 44. CHECK FOR OTHER DTCSWith the scan tool, check DTCs.Is the DTC P2704 present also?YesReplace the Transmission Solenoid/TRS Assembly per the Service Information. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE/TRANS SOLENOID/TRS ASSY - REMOVAL)Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 55. CHECK THE DTC EVENT DATAWith the scan tool, read and record the DTC EVENT DATA.Make sure to record all DTC EVENT DATA stored in the scan tool for future reference in this test procedure.Does the DTC EVENT DATA display information for the DTC P0876?YesGo To 6NoRefer to the Transmission category and perform the diagnostics for the DTC listed in the DTC EVENT DATA. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - DIAGNOSIS AND TESTING) 6. CHECK IF DTC EVENT DATA WAS SET IN PARK, NEUTRAL OR REVERSERefer to the DTC EVENT DATA recorded earlier.Did the DTC P0876 set in Park, Neutral, or Reverse?YesGo To 10NoGo To 77. CHECK THE UD PRESSURE SWITCH STATUSRefer to the DTC EVENT DATA recorded earlier.Did the DTC P0876 set with the UD Pressure Switch closed?YesGo To 10NoGo To 88. CHECK THE LINE PRESSUREIn the DTC EVENT DATA recorded earlier, compare the Line Pressure and the Desired Line Pressure.Is the Line Pressure less than 40 psi, and significantly below the Desired Line Pressure?YesRepair as necessary to correct low line pressure. Check fluid level and adjust as necessary. If fluid level is OK, check the Primary Oil Filter seal for a split, crack, or improperly installed. If the filter and seal are OK, check the Main Regulator Valve in the Oil Pump. Refer to the Service Information for the above procedures.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 99. CHECK THE (T29) UD PRESSURE SWITCH SENSE CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT

Turn the ignition off to the lock position.Disconnect all PCM harness connectors.Disconnect the Transmission Solenoid/TRS Assembly harness connector.Measure the resistance between the (T29) UD Pressure Switch Sense circuit and all other circuits in the Transmission Solenoid/TRS Assembly harness connector.Is the resistance below 5.0 ohms between the (T29) UD Pressure Switch Sense circuit and any other circuit(s) in the Transmission Solenoid/TRS Assembly harness connector?YesRepair the (T29) UD Pressure Switch Sense circuit for a short to another circuit(s).Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoReplace the Transmission Solenoid/TRS Assembly per the Service Information. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE/TRANS SOLENOID/TRS ASSY - REMOVAL)Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST.10. CHECK THE PCM AND WIRINGTurn the ignition off to the lock position.Remove the Ignition Switch Feed fuse from the TIPM.Removal of the Ignition Switch Feed fuse from the TIPM will prevent the vehicle from being started in gear. The Ignition Switch Feed fuse must be removed from the TIPM. Failure to do so can result in personal injury or death.Install the Transmission Simulator, Miller tool #8333.Ignition on, engine not running.With the Transmission Simulator, turn the Pressure Switch selector switch to the UD position.With the scan tool, monitor the UD Pressure Switch state while pressing the Pressure Switch Test button on the Transmission Simulator.Did the state of the UD Pressure Switch change while pressing the Pressure Switch Test button?YesGo To 14NoGo To 1111. CHECK THE (T29) UD PRESSURE SWITCH SENSE CIRCUIT FOR AN OPEN

Turn the ignition off to the lock position.Disconnect the Transmission Simulator, Miller tool #8333.Disconnect the PCM C4 harness connector and connect Miller tool #8815.Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install Miller tool #8815 to perform diagnosis.Measure the resistance of the (T29) UD Pressure Switch Sense circuit between the Transmission Solenoid/TRS Assembly harness connector and the appropriate terminal of the Miller tool #8815.Is the resistance above 5.0 ohms?YesRepair the (T29) UD Pressure Switch Sense circuit for an open.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1212. CHECK THE (T29) UD PRESSURE SWITCH SENSE CIRCUIT FOR A SHORT TO GROUND

Measure the resistance between ground and the (T29) UD Pressure Switch Sense circuit.Is the resistance below 5.0 ohms?YesRepair the (T29) UD Pressure Switch Sense circuit for a short to ground.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1313. CHECK THE (T29) UD PRESSURE SWITCH SENSE CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT

Disconnect all PCM harness connectors.Make sure the Transmission Solenoid/TRS Assembly harness connector is disconnected.Measure the resistance between the (T29) UD Pressure Switch Sense circuit and all other circuits in the Transmission Solenoid/TRS Assembly harness connector.Is the resistance below 5.0 ohms between the (T29) UD Pressure Switch Sense circuit and any other circuit(s) in the Transmission Solenoid/TRS Assembly harness connector?YesRepair the (T29) UD Pressure Switch Sense circuit for a short to another circuit(s).Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoUsing the schematics as a guide, check the Powertrain Control Module (PCM) terminals for corrosion, damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems are found, replace the PCM per the Service Information. With the scan tool, perform QUICK LEARN.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) 14. PERFORM A WIGGLE TEST USING THE TRANSMISSION SIMULATORPerform the steps in the previous test while wiggling the wiring harness and connectors pertaining to the UD Pressure Switch.Did the state of the UD Pressure Switch change while pressing the Pressure Switch Test button?YesRepair the wiring harness and/or connectors as necessary.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1515. CHECK THE TRANSMISSION SOLENOID/TRS ASSEMBLY FOR A SHORT TO GROUND

Disconnect the Transmission Simulator and reconnect the Transmission Solenoid/TRS Assembly harness connector.Disconnect the PCM C4 harness connector and connect Miller tool #8815.Measure the resistance between ground and the (T29) UD Pressure Switch Sense circuit in the appropriate terminal of Miller tool #8815.Is the resistance below 5.0 ohms?YesReplace the Transmission Solenoid/TRS Assembly per the Service Information. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE/TRANS SOLENOID/TRS ASSY - REMOVAL)Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoGo To 1616. CHECK IF THE DTC RESETSReconnect all previously disconnected connectors.With the scan tool, erase all transmission DTCs.Test drive the vehicle. Using the DTC EVENT DATA recorded earlier, try to duplicate the conditions in which the DTC originally set.Does the DTC P0876 reset?YesGo To 17NoGo To 1817. CHECK FOR A CUT NO. 2 CHECK BALLRemove the Valve Body per the Service Information.Check the No. 2 check ball for cuts or damage.Is the No. 2 check ball cut or damaged?YesReplace the No. 2 check ball. Check for excessive clutch debris in the oil pan. If excessive debris is present, check the UD Clutch and repair as necessary.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoReplace the Transmission Solenoid/TRS Assembly per the Service Information. Check for excessive clutch debris in the oil pan. If excessive debris is present, check the UD Clutch and repair as necessary.(Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE/TRANS SOLENOID/TRS ASSY - REMOVAL)Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) 18. CHECK FOR INTERMITTENT WIRING AND CONNECTORSThe conditions necessary to set this DTC are not present at this time.Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.Wiggle the wires while checking for shorted and open circuits.With the scan tool, check the DTC EVENT DATA to help identify the conditions in which the DTC was set.Were there any problems found?YesRepair as necessary.Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - STANDARD PROCEDURE) NoTest Complete.