For a complete wiring diagram Refer to Section 8W.When Monitored:With the ignition on.Battery voltage between 10 and 16 volts.IOD fuse installed.TIPM is configured correctly.Set Condition:Bus messages not received from the ASBS for approximately 2 to 5 seconds.Possible Causes(D65) CAN C BUS(+) CIRCUIT SHORTED TO VOLTAGE(D64) CAN C BUS(-) CIRCUIT SHORTED TO GROUNDDTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGESTIPM NOT CONFIGURED CORRECTLYAUTOMATIC SWAY BAR SYSTEM MODULE POWER AND GROUNDAUTOMATIC SWAY BAR SYSTEM MODULEMODULE THAT SET THIS DTC1. VERIFY DTC IS ACTIVEEnsure the IOD fuse is installed and battery voltage is between 10 and 16 volts before proceeding.With the scan tool, read active DTCs.Is this DTC active?YesGo To 2NoRefer to the Stored Lost Communication diagnostic procedure. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING).2. CHECK FOR ANY OF THE FOLLOWING ACTIVE DTCSWith the scan tool, read all active DTCs from all modules.Check for TIPM configuration, CAN C hardware electrical, VIN Missing/Mismatch, battery or ignition related DTCs.Does the scan tool display any active DTCs to the conditions listed above?YesDiagnose and repair the DTC. Refer to the Index for a complete list of the symptoms.NoGo To 33. VERIFY THAT THE ASBS IS ACTIVE ON THE BUSTurn the ignition on.With the scan tool, select Network Diagnostics.Verify that the ASBS is active on the bus.Is the ASBS active on the bus?YesGo To 4NoPerform the No Response diagnostic procedure. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING).4. CHECK FOR ADDITIONAL COMMUNICATION RELATED DTCSWith the scan tool, select Network Diagnostics.Is there more than one module with active DTCs “Logged Against” the ASBS?YesReplace/update the ASBS in accordance with the service information.Perform the BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).NoGo To 55. CLEAR DTC IN MODULE SETTING FAULTWith the scan tool, select the module setting the DTC against the ASBS.Clear active DTCs.Is this DTC still active?YesReplace/update the module that set this DTC in accordance with the service information.Perform the BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).NoGo To 66. CYCLE IGNITIONCycle the ignition from RUN to OFF three times ending with the key in the RUN position.Does this DTC become active?YesGo To 7NoThe condition is not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring for chafed, pierced, pinched, and partially broken wires and the wiring harness connectors for broken, bent, pushed out, and corroded terminals.Perform the BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).7. CHECK FOR ADDITIONAL LOST COMMUNICATION FAULTSWith the scan tool, select Network Diagnostics.Does the TIPM and other CAN C BUS modules show Lost Communication with the remaining CAN C BUS modules?YesGo To 8NoReplace/update the module that set this DTC in accordance with the service information.Perform the BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).8. (D65) CAN C BUS (+) CIRCUIT SHORTED TO VOLTAGEMeasure the voltage between the (D65) CAN C Bus (+) circuit and ground.Is the voltage above 5 volts?YesRepair the (D65) CAN C Bus (+) circuit for a short to voltage.Perform the BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).NoGo To 99. (D64) CAN C BUS (-) CIRCUIT SHORTED TO GROUNDTurn the ignition off.Measure the resistance between ground and the (D64) CAN C Bus (-) circuit.Is the resistance below 10K Ohms?YesRepair the (D64) CAN C Bus (-) circuit for a short to ground.Perform the BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).NoReplace/update the module that set this DTC in accordance with the service information.Perform the BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).