For a complete wiring diagram Refer to Section 8W.When Monitored:With the ignition on, the Occupant Restraint Controller (ORC) monitors the voltage on the Driver Seat Belt Retractor Tensioner circuits.Set Condition:The ORC detects voltage on the Driver Seat Belt Retractor Tensioner circuits.Possible Causes(R55) DRIVER SEAT BELT RETRACTOR TENSIONER LINE 1 CIRCUIT SHORTED TO BATTERY(R53) DRIVER SEAT BELT RETRACTOR TENSIONER LINE 2 CIRCUIT SHORTED TO BATTERYDRIVER SEAT BELT RETRACTOR TENSIONEROCCUPANT RESTRAINT CONTROLLER (ORC)1. DETERMINE ACTIVE OR STORED DTCEnsure the battery is fully charged.The scan tool, SRS Airbag Load Tool 8443, and DVOM are required to perform the following test.Select Active or Stored DTC.Is the DTC active or stored?ORC - ACTIVE DTCGo To 2 ORC - STORED DTCGo To 52. CHECK FOR SHORTED DRIVER SEAT BELT RETRACTOR TENSIONER

To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.Disconnect the Driver Seat Belt Tensioner connector.Check connectors - Clean and repair as necessary.Connect the 8443 Load Tool and 8443-10 Jumper to the Driver Seat Belt Retractor Tensioner connector.To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.With the scan tool, read the active ORC DTC.Does the scan tool display: B1C39-1ST ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT HIGH?YesGo To3NoReplace the Driver Seat Belt Retractor Tensioner in accordance with the Service Information.Perform *ORC VERIFICATION TEST - VER 13. CHECK (R55) DRIVER SEAT BELT RETRACTOR TENSIONER LINE 1 CIRCUIT AND (R53) DRIVER SEAT BELT RETRACTOR TENSIONER LINE 2 CIRCUIT FOR A SHORT TO BATTERY

To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.Disconnect the 8443 Load Tool and Jumper from the Driver Seat Belt Retractor Tensioner connector.Disconnect the ORC connectors.Check connectors - Clean and repair as necessary.Connect the Load Tool ORC 8443-32-L Adaptor to the ORC connectors.The IP Harness is always connected to the right side (C1) of the 8443-32-L Adapter.Measure the voltage of the (R55) Driver Seat Belt Retractor Tensioner Line 1 circuit between the Driver Seat Belt Tensioner connector and ground.Measure the voltage of the (R53) Driver Seat Belt Retractor Tensioner Line 2 circuit between the Driver Seat Belt Tensioner connector and ground.Is there any voltage present on either circuit?YesRepair the Driver Seat Belt Retractor Tensioner circuits with voltage present for a short to battery.Perform *ORC VERIFICATION TEST - VER 1NoGo To 44. REPLACE THE ORCTo avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment and serious or fatal injury.RepairReplace the ORC in accordance with the Service Information.Perform *ORC VERIFICATION TEST - VER 15. STORED ORC DTCWith the scan tool, record and erase all DTC from all Airbag System Modules.If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contaminated terminals.The following additional checks may assist you in identifying a possible intermittent problem.Reconnect any disconnected components and harness connector.To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.With the scan tool monitor active codes as you work through the following steps.Wiggle the wiring harness and connectors of the related airbag circuit or component.If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop to stop.If only stored codes return continue the test until the problem area has been isolated.In the previous steps you have attempted to recreate the conditions responsible for setting active DTC in question.Are any ACTIVE DTC present?YesSelect the appropriate diagnostic procedure from the Table of Contents in this section.NoNo problem found at this time. Erase all codes before returning vehicle to customer.