For a complete wiring diagram Refer to Section 8W.When Monitored:During power-up, the Occupant Restraint Controller (ORC) and Occupant Classification Module (OCM) monitors the CAN bus for the VIN message.Set Condition:This DTC will set if the VIN information received from the Powertrain Control Module (PCM) is different from the stored VIN.Possible CausesINCORRECT VIN PROGRAMMED INTO THE PCMOCCUPANT CLASSIFICATION MODULE (OCM)1. CHECK FOR ACTIVE DTCTroubleshoot any Ignition, Battery, Seat Weight Sensor, or OCM Internal DTC BEFORE proceedingEnsure that the battery is fully charged.This DTC cannot be cleared until the *OCM SYSTEM VERIFICATION TEST has been completed successfully. With the scan tool, read DTC.Select the module and DTC type.OCM-Active Go To 2 OCM-Stored Erase code with scan tool, test complete.2. CHECK THE VIN STORED IN THE PCMWith the scan tool, compare the VIN that is stored in the PCM to the VIN of the vehicle's VIN plate.Does the VIN stored in the PCM match the vehicle's VIN?YesGo To 3NoReplace and Configure the Powertrain Control Module in accordance with the service information.Perform *(NGC) POWERTRAIN VERIFICATION TEST VER - 5. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).3. PERFORM THE OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TESTEnsure that the battery is fully charged.The Occupant Classification Seat Weights 9077 are required to perform this test.Verify that the passenger seat is empty.Remove any special tools or jumper wires and reconnect all previously disconnected components – except the battery.To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.Failure to follow the test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: verify that all tests steps that led you here were performed as directed; verify that the ignition is in run; Wait 30 seconds after changing the seat weight before proceeding to allow the system to stabilize; only press scan tool buttons when directed to do so; and perform the Occupant Classification Module System Verification Test to completion.With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, wait two minutes, and then proceed as follows.With the scan tool, read OCM DTC.Does the scan tool display any active: B2206-CURRENT VIN MISSING/MISMATCH DTC?Yes Go To 4No Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.4. PERFORM OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TESTTo avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.Verify that the passenger seat is empty.Verify that all of the Seat Weight Sensor mounting screws are tightened to torque specification. Refer to Group 23 for specification.Failure to follow the test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: verify that all tests steps that led you here were performed as directed; verify that the ignition is in run; Wait 30 seconds after changing the seat weight before proceeding to allow the system to stabilize; only press scan tool buttons when directed to do so; and perform the Occupant Classification Module System Verification Test to completion.To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, proceed as follows.With the scan tool, read OCM DTC.Does the scan tool display active: B2206-CURRENT VIN MISSING/MISMATCH?YesTo avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.Replace the OCM in accordance with the Service Information.Replace the Service Kit if a seat from another vehicle was installed. Perform *OCM SYSTEM VERIFICATION TEST.No - But Other DTC PresentDiagnose and repair the other DTC. Refer to the Table of Contents in this Section for a complete list of symptoms.No - No Active DTC PresentErase all codes before returning vehicle to customer.